NEW QUESTION 1


A)

B)

C)

D)

• A. Option A
• B. Option B
• C. Option C
• D. Option D

Answer: D

NEW QUESTION 2

Which type of IPv6 address is similar to a unicast address but is assigned to multiple devices on the same network at the same time?

• A. global unicast address
• B. anycast address
• C. multicast address
• D. link-local address

Answer: B

NEW QUESTION 3

Refer to the exhibit.

An IP subnet must be configured on each router that provides enough addresses for the number of assigned hosts and anticipates no more than 10% growth for now hosts. Which configuration script must be used?
A)

B)

C)

D)

• A. Option A
• B. Option B
• C. Option C
• D. Option D

Answer: C

NEW QUESTION 4

Refer to the exhibit.

A network engineer is updating the configuration on router R1 to connect a new branch office to the company network R2 has been configured correctly. Which command must the engineer configure so that devices at the new site communicate with the main office?

• A. ip route 172.25.25 0 255 255 255.0 192.168.2.1
• B. ip route 172.25.25 1 255 255 255 255 g0/1
• C. ip route 172.25.25.0.255.255.255.0.192.168.2.2

Answer: C

NEW QUESTION 5

Refer to the exhibit.

What is the issue with the interface GigabitEthernet0/0/1?

• A. Port security
• B. High throughput
• C. Cable disconnect
• D. duplex mismatch

Answer: C

NEW QUESTION 6

Refer to the exhibit.

What action establishes the OSPF neighbor relationship without forming an adjacency?

• A. modify hello interval
• B. modify process ID
• C. modify priority
• D. modify network type

Answer: A

NEW QUESTION 7

Refer to the exhibit.

An engineer assigns IP addressing to the current VLAN with three PCs. The configuration must also account for the expansion of 30 additional VLANS using the same Class C subnet for subnetting and host count. Which command set fulfills the request while reserving address space for the expected growth?

• A. Switch(config)#interface vlan 10Switch(config-if)#ip address 192.168.0.1 265 255.255.252
• B. Switch(config)#interface vlan 10Switch(config-if)#ip address 192.168.0.1 255 255.255.248
• C. Switch(config)#interface vlan 10Switch(config-if)#ip address 192.168.0.1 255 255.255.0
• D. Switch(config)#interface vlan 10Switch(config-if)#ip address 192.168.0.1 255.255.255.128

Answer: B

NEW QUESTION 8

Refer to the exhibit.

Which two values does router R1 use to identify valid routes for the R3 loopback address 1.1.1.3/32? (Choose two.)

• A. lowest cost to teach the next hop
• B. highest metric
• C. highest administrative distance
• D. lowest metric
• E. lowest administrative distance

Answer: DE

NEW QUESTION 9

When DHCP is configured on a router, which command must be entered so the default gateway is automatically distributed?

• A. default-router
• B. default-gateway
• C. ip helper-address
• D. dns-server

Answer: A

NEW QUESTION 10

Which two functions are performed by the core layer in a three-tier architecture? (Choose two)

• A. Provide uninterrupted forwarding service.
• B. Police traffic that is sent to the edge of the network.
• C. Provide direct connectivity for end user devices.
• D. Ensure timely data transfer between layers.
• E. Inspect packets for malicious activity.

Answer: AD

Explanation:
Cisco is very clear about the purpose of this layer. Its only role is to forward traffic, the fastest it can. Here you don’t apply any policy, as you must try to reduce the load of the core so it can focus on routing. https://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/Campus/campover.html#wp708 831

NEW QUESTION 11

Refer to the exhibit.

What are the two steps an engineer must take to provide the highest encryption and authentication using domain credentials from LDAP?

• A. Select PSK under Authentication Key Management
• B. Select WPA+WPA2 on Layer 2 Security
• C. Select Static-WEP + 802.1X on Layer 2 Security
• D. Select WPA Policy with TKIP Encryption
• E. Select 802.1X from under Authentication Key Management

Answer: BE

NEW QUESTION 12
DRAG DROP
Refer to the exhibit.

Drag and drop the networking parameters from the left onto the correct values on the right.

• A. Yes
• B. Not Mastered

Answer: A

NEW QUESTION 13

Refer to the exhibit.

The network engineer is configuring router R2 as a replacement router on the network After the initial configuration is applied it is determined that R2 failed to show R1 as a neighbor Which configuration must be applied to R2 to complete the OSPF configuration and enable it to establish the neighbor relationship with R1?
A)

B)

C)

D)

• A. Option
• B. Option
• C. Option
• D. Option

Answer: D

NEW QUESTION 14

What is the advantage of separating the control plane from the data plane within an SDN network?

• A. decreases overall network complexity
• B. limits data queries to the control plane
• C. reduces cost
• D. offloads the creation of virtual machines to the data plane

Answer: A

NEW QUESTION 15

What facilitates a Telnet connection between devices by entering the device name?

• A. SNMP
• B. DNS lookup
• C. syslog
• D. NTP

Answer: B

NEW QUESTION 16

Which WPA3 enhancement protects against hackers viewing traffic on the Wi-Fi network?

• A. TKiP encryption
• B. AES encryption
• C. scrambled encryption key
• D. SAE encryption

Answer: D

NEW QUESTION 17

What criteria is used first during the root port selection process?

• A. local port ID
• B. lowest path cost to the root bridge
• C. lowest neighbor's bridge ID
• D. lowest neighbor's port ID

Answer: B

NEW QUESTION 18

In which circumstance would a network architect decide to implement a global unicast subnet instead of a unique local unicast subnet?

• A. when the subnet must be available only within an organization
• B. when the subnet does not need to be routable
• C. when the addresses on the subnet must be equivalent to private IPv4 addresses
• D. when the subnet must be routable over the internet

Answer: D

NEW QUESTION 19

What is the function of a server?

• A. It transmits packets between hosts in the same broadcast domain.
• B. It provides shared applications to end users.
• C. It routes traffic between Layer 3 devices.
• D. It Creates security zones between trusted and untrusted networks

Answer: B

NEW QUESTION 20
......